Adhesives for Camera Module Assembly
UV
Heating
Moisture
UV + Heating
UV + Moisture
2 Component
1. 렌즈 고정용
- UV or UV+Heating Curing
- Good adhesion
- Low transmittance
- Low reflectivity
- No flare
- Good curing depth
- High thixotropy
2. 플렌지 고정용
- UV Curing
- Good adhesion
- Excellent curing depth
- Good workability
- Excellent reliability
2. 플렌지 고정용
- UV Curing
- Good adhesion
- Excellent curing depth
- Good workability
- Excellent reliability
3. Barrel 고정용
- Good adhesion
- Low shrinkage
- Dual cure (UV+heat)
4. IR Filter 접착용
- Good adhesion
- Low RBO
- Low temp cure
5. Die attach
- Low temp cure
- Low warpage
- Fast cure
6. Housing attach
- High adhesion to LCP, PA
- Low temp cure
- Fast cure
- Dual cure (UV+heat)
1. 렌즈 고정용
렌즈 고정용 레진이란?
렌즈와 Barrel의 접착을 목적으로 사용되는 UV 경화형 Resin.
제품의 특성
Good adhesion
탈거력 우수 신뢰성 개선
No Flare
반사율과 투과율이 낮음 빛의 반사로 인한 플레어 현상 개선
Good curing depth
심부 경화가 우수 작업 속도 향상, 불량률 개선
High thixotropy
칙소성 우수 Gate(hole) 막힘 개선
물성표
품명 | Curing Condition | Viscosity [cP] | Thixotropic Index | Hardness [D type] |
---|---|---|---|---|
UC-1003B 시리즈 | 2,000mJ/cm2 | 2,000 ~ 20,000 | 2.0 ~ 6.0 | 30 ~ 80 |
TB-1QUS-RE(V4) | 2,000mJ/cm2, 80℃ / 30min | 10,000 ~ 15,000 | 2.0 ~ 4.0 | 50 ~ 70 |
2. 플렌지 고정용
플렌지 고정용 레진이란?
VCM과 Flange의 접착을 목적으로 사용되는 UV 경화형 Resin.
제품의 특성
Good adhesion
탈거력 우수 신뢰성 개선
Vision inspection
형광물질을 이용한 비전검사 가능 불량률 개선
High thixotropy
칙소성 우수 VCM과 Flange 사이 넓은 모델에도 안정적으로 도포
Good curing depth
심부 경화가 우수 작업 속도 향상. 불량률 개선
물성표
품명 | Curing Condition | Viscosity [cP] | Thixotropic Index | Hardness [D type] |
---|---|---|---|---|
UC-133B 시리즈 | 2,000mJ/cm2 | 2,000 ~ 8,000 | 1.5 ~ 2.5 | 50 ~ 60 |
UC-1355 시리즈 | 2,000mJ/cm2 | 3,000 ~ 8,000 | 2.0 ~ 5.0 | 40 ~ 80 |
3. Barrel 고정용
Barrel
Barrel과 리테이너를 영구적으로 조립 완성하는 작업에서 본딩 도포 및 경화 공정에 사용되는 열 경화형 Resin.
제품의 특성
- - 최적화 된 점도/칙소
- - 일정한 높이의 penetration
- - 경화 후 45kgf 이상의 우수한 접착력
- - Dual cure : UV 가경화 후 Thermal 경화 시 변화율 0.22% 이하
물성표
SAC-9663 | TB-1QUS-LB | ||
---|---|---|---|
Main component | Epoxy Only heat | Epoxy + Acrylate UV+ Heat system |
|
Appearance | Black | Dark gray | |
Curing condition | Heat | 80℃ x 20min | 80℃ x 30min |
UV [mJ/cm2] | 2,000 |
4. IR Filter 접착용
IR Filter attach
적외선은 차단하고 가시광선을 투과시켜 영상을 구현하는 디지털 영상장치의 부품인 IR filter와 Holder를 접착하는 열 경화형 Resin.
제품의 특성
- - 4 point dotting 공정에 적합한 점도/칙소
- - Low viscosity type으로 dotting 퍼짐성 우수
- - Film filter or glass filter에 우수한 접착력
- - Low Reins Bleed Out
- - 저온 속경화 가능
적용사례
- - SAC-9640 : 저 화소 5M 제품에 적합
- - SAC-9640-15 : 고 화소 48M or 68M 제품에 적합
물성표
SAC-9640 | SAC-9640-15 | UC-199F | |
---|---|---|---|
Main component | Epoxy Only heat | Epoxy Only heat | Urethane Acrylate |
Appearance | Black | Black | Light yellow |
Curing condition | 80℃ x 30min | 80℃ x 20min | 2,000mJ/cm2 |
5. Die attach
Die attach
PCB 기판 위 특정위치 패턴을 화상인식하여 Image sensor를 일정한 위치에 붙이고 경화시키는 열 경화형 Resin.
제품의 특성
- - 공정에 적합한 점도/칙소 : Tilt 우수
- - Dispensing 공정 작업성 우수
- - Low warpage
- - Metal에 대한 접착성능이 우수하며 Soft or hard type 별 제품군 형성
- - 80℃ or 120℃ 조건에서 속경화 가능
적용사례
- - SDA-9000 : 저 경도, 저 modulus 특성 및 80℃ x 2min 속 경화 요구되는 모델에 적합
- - SDA-9505 : 매우 높은 접착력이 요구되고, 120℃ x 2min 방식 요구 모델에 적합
물성표
SDA-9000 | SDA-9505 | |
---|---|---|
Main component | Epoxy Only heat | Epoxy Only heat |
Appearance | Black / Ivory | Black / Red |
Curing condition | 80℃ x 2min | 120℃ x 2min |
6. Housing attach
Housing attach
Image sensor가 실장된 기판의 테두리에 렌즈가 부착된 하우징 모듈의 접착을 목적 사용되는 열 or UV + 열 경화형 Resin.
제품의 특성
- - Dispensing 작업성 우수
- - 점도 / 칙소별 여러가지 제품이 있어 공정 속도에 따라 적용 가능
- - LCP / PPA 재질에 대한 우수한 접착성능
- - 낙하 테스트 및 신뢰성 후 접착력 감소폭 적음
- - 저온 속경화 가능
적용사례
- - SAC-9626 / SAC-9836 : 저 경도, 저 modulus 특성으로 특히 내충격이 요구되는 모델에 적합
- - TB-1QUS-C11 : Dual cure 방식으로 우수한 접착력
물성표
SAC-9626 | SAC-9836 | SAC-9826 | TB-1QUS-C11 | ||
---|---|---|---|---|---|
Main component | Epoxy Only heat | Epoxy Only heat | Epoxy Only heat | UV+ Heat system | |
Appearance | Black | Black | Black | Dark gray | |
Curing condition | Heat | 80℃ x 30min @ dry oven |
80℃ x 30min @ dry oven |
80℃ x 30min @ dry oven |
80℃ x 30min |
90℃ x 3min @ hot-plate |
90℃ x 3min @ hot-plate |
90℃ x 3min @ hot-plate |
|||
UV [mJ/cm2] | 2,000 |